Iso 16750 5 pdf
Rating: 4.6 / 5 (2983 votes)
Downloads: 84241

CLICK HERE TO DOWNLOAD

for each load type, several requirement classes are defined. this document applies to electric and electronic systems and components for vehicles including electric propulsion systems and components with maximum working voltages according to voltage class b. this fourth edition cancels and replaces the third edition ( iso: ), which has been technically revised. this test checks the dut for malfunctions and breakage caused by shock of door slamming. apply the following test simultaneously to all applicable inputs ( connections) of the dut. failure mode is mechanical damage ( e. iso: describes the potential environmental stresses and specifies tests and requirements recommended for the specific mounting location on/ in the road vehicle. iso 16750, road vehicles – environmental conditions and testing for electrical and electronic equipment, is a series of iso standards which provide guidance regarding environmental conditions commonly encountered by electrical and electronic systems installed in automobiles and specify requirements and tests. iso: specifies chemical loads and corresponding tests and requirements for the mounting of electric and electronic systems and components on road vehicles. iso: applies to electrical and electronic systems/ components for road vehicles. this part of iso 16750 specifies the chemical loads that can affect electric and electronic systems and components in respect of their mounting location on or in road vehicles, and specifies the corresponding tests and requirements. the main changes are as follows:? it does not cover electromagnetic compatibility ( emc). 12) ; — subdivision of test methods in temperature cycle test for application to duts of " small and. ⎯ part 4: climatic loads. iso 16750 consists of the following parts, under the general title road vehicles — environmental conditions and testing for electrical and electronic equipment: — part 1: general — part 2: electrical loads — part 3: mechanical loads — part 4: climatic loads — part 5: chemical loads. isowas prepared by technical committee iso/ tc 22, road vehicles, subcommittee sc 3, electrical and electronic equipment. view the most recent version. change of table 2 ) ;. this part of iso 16750 describes the potential environmental stresses and specifies tests and requirements recommended for the specific mounting location on/ in the road vehicle. in accordance with adobe' s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. this part of iso 16750 applies to electrical and electronical systems/ components for road vehicles. the load occurs on closures when slammed shut. the iso 16750 series describes environmental conditions and tests to be applied to electrical and electronic equipment directly mounted in or on the vehicle. iso: ( e) the concept of the iso 16750 series is to define requirement classes for separate load types. constitutes following references, requirements of document. for example, the iso 16750 series should not be. this second edition cancels and replaces the first edition ( iso: ), which has been technically revised. iso: ( e) pdf disclaimer. integrating and harmonizing contents from iso: ( e. [ 1] iso 16750 has five parts:. this third edition cancels and replaces the second edition ( iso: ), which has been technically revised. a detached capacitor inside the housing of an electronic control module due to the high accelerations caused by door slamming). in references, such a way ( all parts), referenced document ( including or amendments) road road vehicles — fuse- links vehicles — environmental conditions and testing for electrical and electronic equipment iso:, — part 1: equipment — part 4. ⎯ part 3: mechanical loads. decrease the supply voltage from the minimum supply voltage, usmin, to 0 v, then increase it from 0 v to usmin, applying a change rate of ( 0, 5 ± 0, 1) v/ min linear, or in equal steps of not more than 25 mv. this pdf file may contain embedded typefaces. change of table 2) ; — reorganization of test conditions and application methods in context ( 4. this document has been replaced. the main changes are as follows: — integration and harmonization of contents from iso: ( e. iso 16750 consists of the following parts, under the general title road vehicles — environmental conditions and testing for electrical and electronic equipment: part 1: general part 2: electrical loads. this document was prepared by technical committee iso/ tc 22, road vehicles, subcommittee sc 32, electrical and electronic components and general system aspects. the main changes are as follows: — integrating and harmonizing contents from iso: ( e. it is not intended for direct application iso 16750 5 pdf to parts or assemblies that are part of the equipment. standard by international organization for standardization,. iso 16750 consists of the following parts, iso 16750 5 pdf under the general title road vehicles — environmental conditions and testing for electrical and electronic equipment: ⎯ part 1: general. it is applicable to environmental conditions and tests affecting electrical and electronic equipment mounted directly on or in the vehicle. 2 normative references. every requirement class is determined pdf by a specific code letter. road vehicles - environmental conditions and testing for electrical and electronic equipment - part 5: chemical loads. it describes the potential environmental stresses and specifies tests and requirements recommended for the specific mounting location on. it distinguishes between electrical, mechanical, thermal, climatic and chemical loads. iso 16750 consists of the following parts, under the general title road vehicles — environmental conditions and testing for electrical and electronic equipment: ⎯ part 1: general ⎯ part 2: electrical loads. view all product details. ⎯ part 2: electrical loads.