Fluidmaster instructions pdf
Rating: 4.6 / 5 (3543 votes)
Downloads: 46136

CLICK HERE TO DOWNLOAD

of fill valve by twisting connector nut to the left (clockwise). Replace it if it is worn, or. KA Universalin. If the valve is still filling and the water is up to the line in the bowl, then the amount of water going into the bowl is too high and needs to be adjusted For more detailed instructions and installation videos, please visit our site at & enter • If fill valve has been in use for some time and/or float cup does not drop when flushing tank, replace seal with a genuine Fluidmaster seal (See “IF REPLACING SEAL”). Remove and replace old seal by sliding the seal up and over the valve. Holding flush valve in place, thread large plastic locknut onto threads of flush valve. LS control unit pdf manual download. B: REMOVE OLD LOCKNUT. Color-coded, helpful install tools included for the fastest installation possible 2 Preparing the Flush Valve for Installation. Fluidmaster will not be responsible or liable for use of non Fluidmaster toilet tank parts are found in more toilets than all other brands combined and is the1 brand of toilet repair parts worldwide This Toilet Repair Kit includes: H PerforMAX® toilet fill valve. Always use quality Fluidmaster parts when installing or repairing. Remove tank to bowl gasket and flush valve lock nut first. When adjusting float cup, A. flush tank first. Disconnect the flapper chain/linkage from the lever. Removing Valve Cap Assembly, Flushing Out Debris, Replacing Seal, & Replacing Valve Cap Assembly SEAL LOCATION A SEAL Bwritten Fluidmaster will not be responsible or liable for use of non-Fluidmaster parts during installation or repairing. Unthread nut from old lever. Fluidmaster will not be responsible or liable for use of non-Fluidmaster parts during installation or repair See below for your specific flush valve seal replacement instruction. A control unit pdf manual download Waitminute until the bowl water level recedes down and stops. Before flush valve installation, ensure overflow pipe and water level of tank are correctly setTHE TOP OF OVERFLOW PIPE (A) must be cut 1” below bottom of TANK. To adjust tank water, turn adjustment screw clockwise to raise Installing Flush ValveInsert flush valve into tank hole. IF PART#, Grev,/FLUIDMASTER® ARHR FILL VALVE INSTALLATION INSTRUCTIONS DO NOT USE LIMITED FIVE-YEAR EXPRESS WARRANTY Subject View and Download Fluidmaster LS technology installation instructions online. Position overflow pipe toward back of tank (Do not cover bolt holes of tank). B: WATER LEVEL IS TOO LOW. Turn the tank water level adjustment screw clockwise to raise the float. With a pencil, draw a line at the top of the water level in bowl. NOTE: Inspect water supply connector. Fill Valve. After the water stops filling the tank, the water level should be roughly 1⁄2 inch below the top of overflow pipe to ensure a proper flush/2". Hand tighten locknut and then use large adjustable pliers to go 1⁄2 turn beyond hand tight View and Download Fluidmaster A quick install manual online. Below tank, twist locknut to the A: FLUSH THE TOILET TO CHECK THE TANK WATER LEVEL. Sign In Upload Fluidmaster seal. Towel you don’t know how old it is, to (Optional) prevent flooding and property damage. Replace with Adjusting Tank Water LevelWith water turned on, set float cup to desired level, by. Now flush the toilet. Remove lever from tankFor standard front-mount tanks go to stepFor a SIDE OR ANGLE-MOUNT TANK, slowly bend new lever arm to match For more detailed instructions and installation videos, please visit our site at & enter KH in the search field. Remove water supply connector from bottom. FILL VALVE WITH LEAK SENTRY. Adjustable Flush Valve Repair Kit which includes the flapper. Insert flush valve BA: REMOVE CONNECTOR. Then make adjustment while tank is filling. Flush to reset water level INSTALLATION INSTRUCTIONS FLUIDMASTER ® WHITE TANK LEVER TOOLS NEEDED: ALSO AVAILABLE INRemove tank lid. turning water level adjustment screw. Overflow Pipe. Kohler® AquaPiston (use YELLOW seal): Remove and replace old seal, placing new seal in groove at bottom of canister. LEVER HOLE (B). G Universal Tank-To-Bowl Gasket SystemChrome Tank Lever.