Astm d93 pdf
Rating: 4.5 / 5 (5878 votes)
Downloads: 21836

CLICK HERE TO DOWNLOAD

for multi- user access and pricing, contact sales here or callastm. last previous edition approved in as d93– 10a. department of transportation regulations, see codes. published november. training cannot be shared. because it may not be technically possible to adequately depict all changes accurately, astm recommends that users consult prior editions as appropriate. for annual book of astm standards volume information, refer to the standardõs document summary page on the astm website. 1520/ d0093- 10a. some specifications state a d93 minimum flash point below 40 ° c, however, the precision has not been determined below this temperature. pdf), text file (. org, or ( procedurea), section 12 ( procedure b), and 13 ( procedure c) contact astm customer service at org. for annual book of astm standards volume information, refer to the standard’ s document summary page on the astm website. astm d93- 02a standard test methods for flash- point by pensky- martens closed cup tester. 7 annual book of astm standards, vol 14. once the profile is stored to memory the user can select this option without the need to program the test parameters. 4 these test methods provides the only closed cup flash point test procedures for temperatures up to 370° c ( 698° p). 1 these test methods cover the determination of the flash point of petroleum products in the temperature range from 40 to 360° c by a manual pensky- martens closed- cup apparatus or an automated pensky- martens closed- cup pdf apparatus. 2 procedure a is applicable to distillate fuels ( diesel, biodiesel blends, kerosine, heating oil, turbine fuels), new and in- use lubricating oils, and other homogeneous petroleum liquids not included in the. 1 this test method covers the determination of the flash point of petroleum products in the temperature range from 40 to 360 o c by a manual pensky- martens closed- cup apparatus or an automated pensky- martens closed- cup apparatus. originally approved in 1921. designation: 34/ 99. in all cases only the current version of the standard as published by astm is to be considered the official document. txt) or read online for free. 1 this document is not an astm standard and is intended only to provide the user of an astm standard an indication of what changes have been made to the previous version. astm astm d93 pdf d93 test pdf methods provide the only closed cup flash point test procedures for temperatures up to 370° c or 698° f. 8 available from american national standards institute ( ansi), 25 w. operation is simple, just a single raising or lowering action when loading or removing the test. 0 ( extended ocr). these standards are three of five required method options for determination of the ignitability characteristic in liquid wastes, see. the methods cover the determination of the flash point of petroleum products in the temperature range from 40 to 370° c, and of biodiesel by an automated pensky- martens closed cup apparatus in the temperature range of 60 to 190° c. , 4th floor, new york, ny 10036. apparatus consists of the test cup, test cover and shutter, stirring device, heating source, ignition source device, air bath, and top plate described in detail in annex a1. all astm online courses are available for a 1- year subscription on astm' s learning center for a single user only via username/ password. 2 for referenced astm standards, visit the astm website, www. 9 for information on u. astm d3828 small scale flash point tests reduce the risk by using a small sample of just 2 or 4 ml, by comparison astm d93 pensky- martens methods use 75 ml. note 1— flash point determination as above 250° c can be performed, however, the precisions have not. tested then a test profile can be set up called “ diesel” which conforms to procedure a d93 with an expected flash of 75° c. pensky- martens is a closed- cup test method, meaning that it aims to simulate a liquid spill in a closed environment. internet access is required. most test methods now permit the use of an electric ignition source as an alternative to the traditionally used gas flame with some flash point testers providing users with a choice of either. 6 annual book of astm standards, vol 15. identifier- ark ark: / 13960/ t74t7rm3h ocr abbyy finereader 11. for these method procedures used in the characterization of flash point of liquids. designation: d93 − 19 d93 − 20. astm d93 pdf astm d93- 19 novem standard test methods for flash point by pensky- martens closed cup tester 1. addeddate: 44: 24 identifier gov. 1 these test methods cover the determination of the flash point of petroleum products in the temperature range from 40 ° c to 370 ° c by a manual pensky- martens closed- cup apparatus or an automated pensky- martens closed- cup apparatus, and the determination of the flash point of biodiesel in the temperature range of 60 ° c to 190 ° c by an. 5 annual book of astm standards, vol 14. 4 ignition source— natural gas flame, bottled gas flame, and electric ignitors ( hot wire) have been found acceptable for use as the ignition source. according to astm d93- 20, pensky- martens test procedures can determine the flash point of petroleum products in the 40° c to 370° c range by either manual or automated closed- cup apparatus, as well as determining the flash point. 1 these test methods cover the determination of the flash. 1 these test methods cover the determination of the flash point of petroleum products in the temperature range from 40 ° c to 370 ° c by a manual pensky- martens closed- cup apparatus or an automated pensky- martens closed- cup apparatus, and the determination of the flash point of biodiesel in the temperature range of 60 ° c to 190 ° c by. dflash point by pmcc ( upgraded febfree download as pdf file (. org, or contact astm customer service at org. astm d93 pdf see american society for testing materials ( astm) standard d93- 79, standard d93- 80, or standard d8175- 18. thermometer number temperature range − 5 to + 110° c ( 20 to 230° f) + 10 to 200° c ( 50 to 392° f) + 90 to 370° c ( 200 to 700° f) astm 9c ( 9f) 88c ( 88f) 10c ( 10f) ip 15c 101c 16c. “ astm d93 test methods provide the only closed cup flash point test procedures for temperatures up to 370° c or. 3 available from american national standards institute ( ansi), 25 w.