Ul 817 pdf
Rating: 4.9 / 5 (2234 votes)
Downloads: 66204

CLICK HERE TO DOWNLOAD

however, rewirable plugs and connectors ( e. ( ul) 333 pfingsten road northbrook, ilul standard for safety for cord sets and power- supply cords, ul 817 eleventh edition, dated ma a change is indicated by a note following the affected item. underwriters laboratories inc. ul- 817- revandedread online for free. standard name: cord sets and power- supply cords standard edition and issue date: 12th edition dated ma date of revision: ma, janu, and aug date of previous revision of standard: 11th edition dated j. ul- 817 standard for cord sets and power- supply cords. 1 this standard specifies the requirements for cord sets and power- supply cords employing molded- on or assembled- on fittings, rated 600 v maximum, and intended for use in non- hazardous locations in accordance with the national electrical code, ansi/ nfpa 70. , 355 lexington avenue, new york, new york ul 817 pdf 10017. ul 817 1 scope 1. ipc/ eia- j- std- 001. once approved, the plugs will be stamped with the “ green dot” on the plug face. the following changes in requirements to the standard for cord sets and power- supply cords, ul 817, are ul 817 pdf being proposed: 1. as the voice of the u. addition of requirements related to overcurrent protection on awg extension cord sets. this revision of ansi/ ul 817 is being issued to incorporate the following changes: addition of requirements to allow the use of spt- 1w and spt- 2w for outdoor- use power- supply cords. standard number: ul 817. power strips and taps covered by a voluntary industry consensus, the standard for current taps and adapters, ul 498a) figure 1. 2, circuit- conductor. 2 this standard also specifies the requirements for. current transfer ratio ( ctr: min. 50% at i f = 5ma, vce= 5v) high isolation voltage between input and output ( viso : 5 000v rms) compact dual- in- line package pc817 : 1- channel type pc827 : 2- channel type pc837 : 3- channel type pc847 : 4- channel type. ul certification requirement decision edition 12 published date: octo last revision:. 2 this standard also specifies the requirements for molded- on. the new and/ or revised requirements are. subject 817 bulletin dated: summary of topics. , panel mount devices) are not covered. all products within the scope of the rule are covered by ul 817. pdf the following table provides a non- exhaustive list of examples of extension cords that fall within and outside the scope of the rule. customers who bought this document also bought: ipc- a- 610. • as added safety precautions mega solders the conductors to the plug pins and adds a hog ring to the cable prior to over molding the plug, further increasing cable retention force. standards and conformity assessment system, the american national standards institute ( ansi) empowers its members and constituents to strengthen the u. requirements contained in ul and csa standards. testing requirements under ul and csa( cul) per ul 817. revision to table 10. 1 this standard specifies the requirements for cord sets and power- supply cords employing molded- on or assembled- on fittings, rated 600 v maximum, and intended for use in non- hazardous locations in. 21, ul 498, and ul. ul 817 pdf - cord sets and power- supply cords please note: all interim revisions for this edition available at time of your purchase will be included. acceptability of electronic assemblies ( hardcopy format) mil- std- 883. molded- on attachment plugs and connectors for hospital- grade molded- on nema attachment plugs and connectors, the ul 817 and csa c22. recognized by ul, file no. all cord set and power supply cords employing iecconfigurations that are affixed to flexible cord or cable, and covered under ul 817 and/ or csa c22. standard for cord sets and power- supply cords. ( d) window covering manufacturers association, inc. cord connector with an integral latching mechanism shall be subjected to the applicable tests in tests for cord connectors, section 14, with the mechanism in place and defeated. cord connector of the 1- 15r, 5- 15r, 5- 20r, 6- 15r, or 6- 20r configuration is permitted to be provided with an integral latching mechanism. the following briefly describes requirements found within these north american standards— ul 817, csa c22. requirements for soldered electrical and electronic assemblies. this revision of ansi/ ul 817 is being issued to incorporate the following changes: 1. ul 817 cord sets and power- supply cords. 21 ul certification file, will need to comply with ulby the effective date of. ul red line edition 12 published date: septem last revision: ansi approved: septem. addition of requirements for an outdoor power supply cord employing spt- 2w and spt- 2rw cord for use in products covered by the standard for seasonal and holiday decorative products, ul 588. bsr/ ul 817, standard for cord sets and power- supply cords proposal. 4) ul 817, standard for cord sets and power- supply cords, 11th edition, dated ma, as revised through febru ( “ ul 817” ), ibr approved for § 1120. ul817ed12- standard for. cord sets and power- supply cordsul 8171 scope1. ul 817 | ul standards & engagement | ul red line | edition 12 | cord sets and power- supply cords | published date: septem | ansi approved: septem. 15 to allow an adapter cord set with a 20 a attachment plug to have both 15 a and 20 a outlets. addition of requirements to include a 14 awg cord set with 6 outlets and overcurrent protective device ( ocp) 2. 4 all extension cord sets employing flexible cord incorporating 18 or 17 awg conductors shall be provided with overcurrent protection ( short circuit and overload. summary of topics. back to standard 817, edition 12. pdf or combination of the two. ul standard edition 12 published date: ma last revision: may 16,. cord sets and power- supply cords. marketplace position in the global economy while helping to assure the safety and health of consumers and the protection of the environment.